網站停更公告：本網站定于2025年07月22日起停止更新，特此公告！
進入手機版
搜 索 |
| 標準編號 | 標準中文名稱 | 標準英文名稱 |
| ANSI/FCI 91-1-1997 | 控制閥門密封的質量標準 | (Standard for Qualification of Control Valve Stem Seals) |
| ANSI/UL 753-1996 | 消防裝置用自動供水控制閥的警報附件 | (Alarm Accessories for Automatic Water-Supply Control Valves for Fire-Protection Service) |
| BS EN 60534-2-5-2003 | 工業過程控制閥.流通能力.通過有段間恢復功能的多段控制閥的流體流量的校準公式 | (Industrial-process control valves - Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery) |
| ASTM F 1985-1999 | 氣力操作的球形控制閥標準規范 | (Standard Specification for Pneumatic-Operated， Globe-Syle， Control Valves) |
| BS EN 60534-3-2-2001 | 工業過程控制閥.尺寸.蝶形閥除外的轉式控制閥的端面距 | (Industrial-process control valves - Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves) |
| BS ISO 15407-2-2003 | 氣壓傳動.五氣口方向控制閥，規格18mm和26mm.有任選電接頭的安裝接口 | (Pneumatic fluid power - Five-port directional control valves， sizes 18 mm and 26 mm - Mounting interface surfaces with optional electrical connector) |
| BS ISO 12238-2001 | 氣壓液動.方向控制閥門.轉換時間的測量 | (Pneumatic fluid power - Directional control valves - Measurement of shifting time) |
| BS ISO 5599-1-2001 | 氣壓液動.五通方向控制閥.不帶電連接器的安裝接口表面 | (Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces without electrical connector) |
| BS ISO 5599-2-2001 | 氣壓液動.五通方向控制閥.任選電氣連接器的安裝接口面 | (Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces with optional electrical connector) |
| BS EN 60534-6-2-2001 | 工業過程控制閥.定位器裝到控制閥的安裝細則.旋轉傳動裝置上安裝的定位器 | (Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators) |
| BS EN 1074-5-2001 | 供水閥門.適用性和專用要求的試驗.控制閥門 | (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Control valves) |
| BS EN 60534-8-3-2000 | 工業流程控制閥.噪聲問題.控制閥的空氣動力噪聲預報法 | (Industrial-process control valves - Noise considerations - Control valve aerodynamic noise prediction method) |
| BS EN 60534-2-3-1998 | 工業過程控制閥.流量.試驗程序 | (Industrial-process control valves - Flow capacity - Test procedures) |
| BS EN 60534-8-1-2001 | 工業過程控制閥.噪聲問題.通過控制閥的動力噪聲的實驗室測量 | (Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves) |
| BS EN 60534-3-1-2000 | 工業過程控制閥.尺寸.帶法蘭的兩路、球型、直立式控制閥門的面對面尺寸和帶法蘭的兩路、球型、角度控制閥門 | (Industrial-process control valves - Dimensions - Face-to-face dimensions for flanged， two-way， globe-type， straight pattern and centre-to-face dimensions for flanged， two-way， globe-type， angle patter) |
| BS EN 1349-2000 | 工業處理控制閥門 | (Industrial process control valves) |
| BS ISO 15407-1-2000 | 18mm和26mm五氣口氣動方向控制閥.無電插頭的安裝界面 | (Pneumatic fluid power - Five-port directional control valves， sizes 18 mm and 26 mm - Mounting interface surfaces without electrical connector) |
| BS ISO 11727-1999 | 氣動流體力學.控制閥和其它元件的控制機械裝置和氣門的識別 | (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components) |
| BS EN 60534-3-3-1998 | 工業過程控制閥.尺寸.對接焊接，兩向，球型，垂直模式控制閥的末端對末端尺寸 | (Industrial-process control valves - Dimensions - End-to-end dimensions for buttweld， two-way， globe-type， straight pattern control valves) |
| BS EN 60534-2-1-1999 | 工業過程控制閥 .流容.安裝條件下液流規模方程 | (Industrial-process control valves - Flow capacity - Flow capacity - Sizing equations for fluid flow under installed conditions) |
| BS ISO 6263-1997 | 液壓傳動.補償式流量控制閥.裝配面 | (Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces) |
| BS ISO 10770-2-1998 | 液壓傳動.電模式液壓控制閥.第2部分:三向流動控制閥的試驗方法 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for three-way directional flow control valves) |
| BS ISO 10770-1-1998 | 液壓傳動.電模式液壓控制閥.第1部分:四向流動控制閥的試驗方法 | (Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for four-way directional flow control valves) |
| BS EN 60534-6-1-1998 | 工業過程控制閥 .控制閥調節器連接用安裝元件.直線傳動裝置上調節器的安裝 | (Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators) |
| BS ISO 7790-1998 | 液壓傳動.規格為03和05型的四油口標準設計疊閥和四油口定向控制閥.緊固尺寸 | (Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves， sizes 02， 03 and 05 - Clamping dimensions) |
EN 60534-8-1-2000
工業過程控制閥 第8部分：噪聲的考慮 第1節：氣動流流徑控制閥產生的噪聲的實驗室測量
Industrial-process control valves - Part 8: Noise consideration; Section 1: Laboratory measurement of noise generated by hydrodynamic aerodynamic flow through control valves (IEC 60534-8-1:1986)
EN 60534-8-4-1994
工業過程控制閥 第8部分：噪聲問題 第4節：流動產生的噪聲的預測
Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994)
EN 60534-8-3-2000
工業流程控制閥 .第8-3部分 噪聲問題 通過控制閥的動力噪聲預測法
Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000)
EN 1074-5-2001
供水閥門 目的要求的適應性和合適的認證試驗 第5部分：控制閥門
Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves
EN 60534-3-1-2000
工業過程控制閥 第３－１部分：尺寸 法蘭雙通球形直型控制閥的端面間距尺寸和有法蘭雙通球型角型控制閥的
Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged， two-way， globe-type， straight pattern and centre-to-face dimensions for flanged， two-way， globe-type， angle pattern control valves (IEC 60534-3-1:2000)
EN 60534-2-1-1998
工業過程控制閥 第2－1部分：流通能力 安裝條件下流體流量的校準公式
Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998)
EN 60534-1-1993
工業過程控制閥 第1部分 控制閥術語和一般考慮
Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987)
EN 60534-3-2-2001
工業過程控制閥 第３部分：尺寸 第２節：無法蘭控制閥（薄型蝶閥除外）的端面間距尺寸
Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001)
EN 60534-3-3-1998
工業過程控制閥 第三部分：尺寸 對接焊接 兩向 球型 垂直模式控制閥的末端對末端尺寸
Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld， two-way， globe-type， straight pattern control valves (IEC 60534-3-3:1998)
EN 60534-6-1-1997
工業過程控制閥 第6－1部分：定位器聯到控制閥執行機構的安裝細則 第1節：直線傳動裝置上調節器的安裝
Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators (IEC 60534-6-1:1997)
EN 60534-6-2-2001
工業過程控制閥 第6－2部分：定位器聯到控制閥執行機構的安裝細則 環形執行機構定位器
Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators (IEC 60534-6-2:2000)
EN 60534-8-2-1993
工業過程控制閥 第8部分 噪聲考慮 第2節通過控制閥的流體產生的噪聲的實驗室測量報法
Industrial-process control valves- Part 8: noise consideration- Section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991)
EN 60534-2-3-1998
工業過程控制閥 第２部分：流通能力 第３節：試驗規程
Industrial-process control valves - Part 2-3: Flow capacity - Test procedures (IEC 60534-2-3:1997)
prEN 13959-2000
公稱壓力在DN6至DN250（含DN250）的防污染控制閥 E族A、B、C和D型
Anti-pollution check valves DN 6 to DN 250 inclusive - Family E， type A， B， C and D
prEN 60534-4-1998
工業過程控制閥 第４部分：檢驗和常規試驗 草案
IEC 60534-4: Industrial-process control valves - Part 4: Inspection and routine testing
EN 1349-2000+AC-2001
工業加工控制閥門
Industrial process control valves
EN 60534-2-5-2003
工業加工控制閥 第2-5部分：流量 通過帶級間恢復多級控制閥的流體尺寸方程
Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery (IEC 60534-2-5:2003) / Note: Endorsement notice
BS ISO 4401-1996
液壓傳動.四油口定向控制閥.裝配面
(Hydraulic fluid power - Four-port directional control valves - Mounting surfaces)
BS EN 60534-1-1989
工業過程控制閥 .第1部分:控制閥術語和一般考慮
(Industrial-process control valves - Industrial-process control valves - Control valve terminology and general considerations)
BS EN 60534-8-4-1994
工業過程控制閥.第8部分:噪聲問題.第4節.流動產生的噪聲的預報
(Industrial-process control valves - Noise considerations - Prediction of noise generated by hydrodynamic flow)
BS EN 60534-8-2-1991
工業過程控制閥.第8部分:噪聲考慮.第2節:通過控制閥的流體產生的噪聲的實驗室測量
(Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves)
BS 6494-4-1989
液壓閥的安裝面.第4部分:03和05規格的四孔組件排氣閥、模數組閥和方向控制閥夾緊尺寸規范
(Hydraulic fluid power valve mounting surfaces - Specification for clamping dimensions of four-part， size 03 and 05， modular stack valves and directional control valves)
BS 5793-4-1987
工業過程控制閥.第4部分:檢驗和例行試驗規范
(Industrial-process control valves - Specification for inspection and routine testing)
BS 5944-4-1984
液壓動力系統和部件所產生的空氣噪音的測量.第4部分:流量和壓力控制閥聲功率級的測定方法
(Measurement of airborne noise from hydraulic fluid power systems and components - Method of determining sound power levels from valves controlling flow and pressure)
BS 5793-5-1984
工業過程控制閥.第5部分:標記規范
(Industrial-process control valves - Specification for marking)
©2008-2023 福建明海鑫企業股份有限公司 閩ICP備07035527號-1 
閩公網安備 35040302610038號
